2020 Jimmy IFS Ultra 4 Red Dragon 4400 Car

2020 Jimmys 4x4 Ultra 4 IFS $295,000.00
For Sale

Phoenix, AZ
Kenneth Goodall  (602)689-0507  Private Message
Call or email

Almost Brand new Jimmys Car, Have raced 2 races. Getting re prepped and ready to race. This is an amazing car and love to drive it but priorities are Changed right now and need to sit on the side lines for a bit. See the amazing build sheet
Next level Dragon 2-seat IFS-Hard Roller
PRO PKG Hard Roller
Fabrication and assembly Full Tig weld (Chassis, Brackets, suspension)

CHASSIS NEXT LEVEL “NL” IFS:
NL “Next Level” IFS FE-"Pro-line" CNC Chromolly chassis / pro line Race
All support tube, 100% tube, Including all dash, Interior, seats
RD-RE2-Slant V2.0 Red Dragon Front Engine 2-seat Version
**Gen III Lower Belly, Wider spread on Trailing Arm’s
**Tig Welded

IFS Roller Hard Part kit; Included
Spidertrax Chromolly 10" front housing,
**7075 Aluminum Billet outer Uprights/Knuckles
**7075 Aluminum Billet Upper A’arms
Lower A'arm chromolly, Billet Ends at all four corners, fully Heat treated
Steering swing set Mount, Heat treated
Tie Rod’s 7075 Aluminum
Complete Hardware kit FK Rod ends, Com bearings
**New for 2020 4140HSTR Nitrate plated spacers/Misalignments
Pair of Unit Bearings 45 spline (2” OD) 6 on 5.5

IFS PARTS;
RCV series 30 Inboard and outboard Race Prep Bolt holes bored and Knurled
33 spine front mid shaft 300M,
Inboard axle stub's 40 Spline
outboard axle stubs, 300M 45 spline outers
Boots, Band’s, Grease and CV-Bolts

**GEN III Rear link set up;
 "Pro-line", 7075 Billet Aluminum Lower Trailing arm kit
(**Uses Pro-Am Large Billet wobble stopper Plates, and Com Bearing at Axle end)
Upper 7075 Billet Aluminum Links
Mounting bracket's at chassis w/Billet weld washers and inner saddle mounts, 

Fabrication; “Brackets” Place and weld only
IFS "Pro Series", “Premier” Turnkey Fabrication;
All Major Mounts, and Race accessories (Com’s, Jack’s, Siren, Mirrors, etc)

IFS Master chassis “RACE” Bracket kit; (Pro-line) 100% complete Turnkey
Belly Skid plate/s (AR-Plate) **Removable
**2-sets, AR Plate KOH and Aluminum rest of the season
Motor mount's, w/Bushings
Motor Head mount kit, w/Bushings
Transmission, w/Bushings
Transfer-case torque mount, w/Bushings
seat tab's, and seat belt
Shock mount kit F&R (Cut away mount's w/Billet weld washers and saddle mount's),
Link Brackets Rear
Limit strap tabs
Radiator Mounting kit (CBR or Ron Davis),
Winch mount and fairlead mount,
Battery tray, (*Options)
Fuel tray / Tube w/Bungs
Dual Remote fill Dry break mounting bracket
Remote fill mount, (*Options, standard is Combo twist/Dry Break)
Transmission shifter
cooler mount's, Transmission, heat exchanger, steering, oil
Brake master pedal mount,
Steering column mount (for a PSC aluminum long column),
steering servo mount,
Limit strap tab's,
seat belt tab's,
Dry Sump Tank Mounting

Spare Driveline and Race Jack Mounted Low in Rear
**Add Jack Mounting Points and Trailer Jack mounting points for prep

Sheet-metal kit; Next Level Full Race Package
Top Dash and Dash Face plate
Floor/firewall,
(*On Single seat Dragon, includes P-Side Sheet metal
Front Kicker's, w/screen
Door's (*option)
bead rolled inner panels and kickers w/stainless screen
Standard Rear window shakers screen w/stainless screen
100% DZUS fastener’s Interior and exterior
**Universal quick release on Hood
full Ducking splash around Radiator (*Replaces standard shaker screen)

Hood
Jeep JK Fiberglass

BOLT KIT;
Front Suspension (A’arms at chassis and at Upright steering Knuckles (qty 12), Tie Rods (qty 4)
Rear Suspension (qty 8)
Motor mounts at chassis (qty 2) (*not at Block)
Head Mounts at Chassis (qty 2) (*not at block)
**12 point, Bolt & Nut 8740 Alloy w/aircraft washer

KING Racing Shocks
2.5x12” RS Coil Carrier with Remote Res
1” shaft upgrade
2.5x16” RS Coil Carrier with Remote Res
1” shaft upgrade
3.0 x 14” Bypass 6 tubes with 1” shaft and ¾ Large Tubes
3.0 x 16” Bypass 6 tubes with 1” shaft and ¾ Large Tubes

Bumps;
Front 2” shorty compact 2.0 Bump with Can
rear Bump Shock Eyelet type

Limiting straps-ELROD's **Double up
set of 8, Includes quad straps, Tabs and Bolts, Fabrication to place and weld 23”-28”

Steering
Steering Power Steering Solutions
3" x 6.0 TT Rack
Machined Spacers for steering Rack
Servo Control Valve
TT "P" Pump w/300M shaft
Pulley 8 groove serp
Hub
Pump mount and alt mount for TT set up
Reservoir set for Relief valve
CBR “Hi-Flow” Billet steering cooler
Relief Valve
Aluminum Steering Column and U-Joints and Steering Mid shaft
PRP Suede Steering wheel w/Push to talk and Horn Tab and 6 bolt adapter

Plumbing
PLUMBING KIT
**Nylon Race Hose
**Hard line on brakes
**qty 2 Line locks on dash

Fuel and Cooling:
Red Dragon “Slant Back” FE 2-seat #PYRO-000592
Custom Pyrocell bladder, foam and .090 internal flange aluminum can with .080 lid. 5" tall baffle wall with 2 ball checks toward front, 10" tall baffle wall with 3 ball checks and 2 baffle walls creating an 8 " wide collector center rear with 4 additional ball checks. Built to drawing #Pyro000592.( Modified Pyro 000206 - Section removed)
parts for fill plate : (1) 6x10 plate - Bolt thru (2) OCG024 Gaskets (24) Bolts (24) Washers (2) 2.25 90 degree tubes (2) Wagon wheel- weld on (2) -10 Pickups (1) -8 Vent roll over valve (2) -8 Return
Fuel sending unit and Gauge
Dual Dry Break Remote fill 2.25x4.5” center w/hose


--------------------------------------------------
Brake kit / JAMAR 19-1 Pedal, Dual Master bracket and Balance-bar
-------------------------------------------------------
COOLING
CBR
CBR 16x12 Trans cooler w/12" fan (2.25 deep)
CBR 21x35 radiator w/heat exch & twin 15" fans (3" deep)
CBR Heat exchanger stand alone

Wiring and Electrical
Finishline Racing(Smitty) Full Chassis and Dash Wiring
Holley Dominator ECU
Holley 12” Dash
2 ECU Masters for all Accessory Controls
Baja Design Ligths


Body and Interior
Jimmys JK body with Bead rolled panels
 
Mechanical and Accessories
DRIVE LINES
Rear Chromolly slip and spline, Balanced, Adams With 1 Spare
Front 934 CV, MW w/speed rated Carrier Bearing Dual shaft 4 yokes
-------------------------------------------------------------- 
Seats
PRP ALPHA Hard Seat
PRP Belts for Neck restraint
----------------------------------------------------------------------
EXHAUST
Headers custom Built

Wheels and Tires
Wheels
Dirtylife Beadlock 6 x 6.5
Tires
BFG 40” Sticky

Lug Nuts Open 5/8 Tapered

Options accessories
Rear Custom 300M sway bar w/Billet arms arms
Front Custom 300M sway bar w/Fabricated arms arms
------------------------------------------------------------------
WINCH Warn 9000RC

Race Kit Options
Window nets
Custom Built swinging SFI certified Nets
------------------------------------------------------------
Race communications;
PCI Elite Race Com, Kenwood radio

Fire Suppression
Safecraft 10LB auto/manual fire suppression system
3 Safecraft Fire Ext. with mounts

Motor:
488 Dart Tall Deck
Dart Tall deck Block
Brodix Heads
Dailey Dry Sump
MSD Intake (Carbon fiber dipped)
Holley 105 TB
Billet Crank
Titanium Rods
Meziere Water Pump
Holley Dominator ECU
Air Cleaner Kit K&N 18x7x7 4” inlet, Tube and Boots w/Foam wrap
Drysump Tank

Transmissions/Kit;
Zero Gravity Th400 in Reid case w/Converter
All Billit internals

Winters shifter w/mount;
Gate shifter

Dipstick
Lokar Race ”

Transfercase;
SCS (Straight Through, 1-1U, 1-1 QC, 1350 yokes)
ORD MAGNUM Box
Single shifter kit AA
Billet adapter


Axle
Brake kit; F&R
Pro series Vented (Spidertrax Hat VR, Wilwood GT Vented Rotors, Wilwood 6P Bridged Calipers and Pads
6.5BC Mounting
TubeWorks TW-CrossTie X-LP Billet Ford 9" / 10" Third Member Extreme, ARB 40 spline
**w/Dual Load Bolt
=================================================
SPIDER 9 REAR
4.0 x .25, Pro series housing
Rear Floater cup for 4.0 Tube
GW 45 spline UNIT BEARING, 6 on 6.5 LUG with race series shanked 5/8 studs,
**with dual Load Bolt
Master Rear Axle and Bracket kit; "Pro-Line"
Back brace with upper towers and Bump stop landing pad's, with Billet weld washers and inner saddle mounts
Lower link mounts with billet weld washers and inner saddle mounts
Axle Shafts (Includes S&H and assembly)
300M axle 45 spline shaft kit Gun Drilled
**Rear Pinion Guard
**Assembly Labor is Included in Master Fabrication

    Off Road Race Vehicles   Listing #177539   Posted: Jul 15 Expires: Aug 24