ID# 168034Posted Nov 23
2003 ford f150
BTF fab Race long travel kit, 4130 boxed control arms, 1"upper uniball and heimed arms with bump pads, 1.5" uniball lowers with bushings, fabbed spindles set up for D44 hubs and factory f150 brake calipers. Comes with an H&M fabbed center drag link to convert to heim steering. Never been ran before, only used to roll the truck around. $2500
Also have a one piece glass hood and mini fenders for 350 and bedsides for 300.
ID# 170840Posted Nov 21
King 2.5 Air shocks
8” inches of travel
Extended length 24.5 eyelet to eyelet
Never been mounted, brand new
ID# 170800Posted Nov 19
4 16" 3.0
Pure Race King Shocks 3 tube Bypass.
New Mounted for Build and used only for Photo shoot. Shafts and bodies prefect no damage.
compressed 26.75 inches
extended 43.25 inches
Will split up
ID# 170732Posted Nov 17
Currie 3rd members
both low pinion
both used only a few times
front - detroit locker, 35 spline, billet pinion support
rear - spool, 40 spline
both 3.25 strange case
both 1350 billet yoke
rear has small damage to pinion and ring gear so I will price accordingly. Will not cost much to fix.
Front and rear cost me over $4000.00. Mostly used for mock up and a few trips to glamis. No rocks.
Cash or will trade for tools or parts or tires.
ID# 170634Posted Nov 15
0 Toyota 4Runner & FJ
The Toyota Differential will bolt into a 2003 - 2009 4Runner & 2007 - 2010 FJ
The Axle Bearings, 3rd Member Bearings and seals - new with only 10K miles
The assembly is fresh and ready to install and run - I'm selling the setup because I'm installing a 1 Ton rear axle setup for 39" tires.
ARB Air Locker
Nitro Chromoly Axle
4" lift Rear Coil Springs
AllPro 2" Lower Control Arms with Johnny Joint rod ends
Diff Housing Armor plates
Lower Control Arm Armor Covers - front and rear
New Brake lines
ABS wiring and sensors
Disc Brakes and rotors
This is a complete setup and ready to bolt in you 4runner or FJ
Please call or txt me if you have any questions 858-774-7503
ID# 168971Posted Nov 14
0 Chevrolet LS7
GM LS7 427 cu.in., $21,000.00
Built By: Jeff Ginter Racing Engines (JGRE)
Approximately 800 race miles on this engine.
Without Dailey Dry Sump System deduct $1,000.00
• Factory GM LS7 Engine Block
• Factory GM LS7 Cylinder Heads
• ARP Head & Main Studs
• Factory GM Rocker Arms with Trunnion Conversion Kit
• Hydraulic Roller Camshaft
• Tie Bar Style Hydraulic Roller Lifters
• Double Roller Timing Chain Set
• Diamond 12.5-1 High Compression Pistons = Race Gas Only
• Total Seal Ring Set
• Clevite Engine Bearings
• Callies Forged Magnum Crankshaft = 4.000 Stroke
• Callies Ultra “H” Beam Billet Connecting Rods = 6.125
• Manley Valve Train = Springs, Retainers, Locks
• Manton Pushrods
• Billet Valve Covers
• LS7 Ignition Coils
• FAST 102mm LSXR Intake Manifold
• Fast 102 MM Throttle body
• FAST Billet Fuel Rails
• Bosch Fuel Injectors
• Dailey Dry Sump System with Torque Converter Pump
ID# 170477Posted Nov 09
2018 Chevrolet LS7
Less than 4 hours of runtime-
This engine won the 2018 Crandon Ultra4 Race and the Reno Nationals and was built by Redline Performace. It's a 454 CID RHS Tall Deck block with All Pro 285 Heads and a CID intake. Has RCD Gear drive and belt drive cover with crank support. ARE Dry Sump, full billet/forged rotating assembly and Ti intake valves.
850 HP at 8,200 RPM's.
It took multiple attempts to capture the power numbers. We started with larger 295 CC All Pro Heads and had to move back and change cams to match. This is a great package, well sorted and our R&D is our loss and the buyers gain.
ID# 169127Posted Nov 05
0 Culhane Transmission
C6 Culhane transmission rebuild don't now history did not use on project for sale $3200
ID# 170251Posted Nov 02
434 ci small block Chevy Brodix ultralight raised cam block 4” stroke 4.155 bore.
18 degree Brodix heads
QT aluminum rocker arms
Under rocker stud bridge
Billet roller solid lifters
CP forged pistons
Oliver forged rods
Lightened forged crank internally balanced
All ARP hardware
All main bearings are 4 bolt outter bearing are strait bolt inner bearing are cross bolt
Oil dripper valve covers.
4 stage Barnes dry sump pump with Kse power steering and fuel pump attachment.
3 gallon oil tank with prescreen attachment
Inline air/oil passthru cooler
remote hp6a big oil filter remote mount.
Motor is on complete refresh oil pan valve covers dry sump tank and intake all at powdercoat will update picture when I get them back on on motor.
Possibly open to partial or full trade depending on what you have worst I can say is no.
Please text only for questions or inquiries 9517335432 mike
ID# 170133Posted Oct 29
2015 GMC/Chevy Sierra 1500
Selling Brand new Dirt King hangers and Shackles still in packaging with used Deaver U-182 leaf springs for GMC Sierra.